RETIRED ›
This product is no longer available and has been replaced by: CR1000X. Some accessories, replacement parts, or services may still be available.
CR10X Datalogger for Measurement and Control
Services Available
Repair No
Calibration Yes
Free Support No

Resumen

The CR10X provided sensor measurement, timekeeping, data reduction, data/program storage and control functions. The CR10X stored up to 62,000 data points. Data and programs were stored either in a nonvolatile Flash memory or RAM. A lithium battery backed up the RAM and real-time clock. The CR10X also suspended execution when primary power (BPALK, PS100) dropped below 9.6 V, reducing the possibility of inaccurate measurements.

Read More

Beneficios y características

  • Designed for unattended network applications
  • Stores 62,000 data points (nonvolatile)
  • Data format options are mixed array (default) or table
  • Detachable keyboard/display, the CR10KD, can be carried to multiple stations

Images

Descripción técnica

The data logger consisted of a CR10XM Measurement and Control Module and black CR10X Wiring Panel.

The CR10X provided sensor measurement, timekeeping, data reduction, data/program storage and control functions. The CR10X stored up to 62,000 data points. Data and programs were stored either in a nonvolatile Flash memory or RAM. A lithium battery backed up the RAM and real-time clock. The CR10X also suspended execution when primary power (BPALK, PS100) dropped below 9.6 V, reducing the possibility of inaccurate measurements.

 

Especificaciones

-NOTE- Note: Additional specifications are listed in the CR10X-Series Specifications Sheet.
Memory Up to 62,000 data points
Analog Inputs 12 single-ended or 6 differential (individually configured)
Pulse Counters 2
Switched Voltage Excitations 3
Control/Digital Ports 8
Serial I/O Port 1
Scan Rate 64 Hz
Burst Mode 750 Hz
Analog Volt Resolution To 0.33 µV
A/D Bits 13
Programming Edlog
Data Storage Mixed Array, Table
Telecommunications PakBus, Modbus, Alert

Compatibilidad

A typical field-based CR10X system included:

  • CR10X Measurement and Control Module and Wiring Panel with specified Operating System
  • Alkaline or Sealed Rechargeable Power Supply
  • Weatherproof Enclosure
  • Communications Peripheral(s)
  • Programming and Communications Software
  • Sensors

Downloads

CR10X OS v.1.23 (1.45 MB) 02-04-2010

Execution of this download installs the CR10X Operating System (Mixed-Array) on your computer.  

Note: The Device Configuration Utility is used to upload the included operating system to the datalogger.  Requires an SC32A or SC32B.


CR10X-TD OS v.1.15 (645 KB) 28-03-2006

Execution of this download installs the CR10X Table Data Operating System on your computer.  

Note: The Device Configuration Utility is used to upload the included operating system to the datalogger.  Requires an SC32A or SC32B.


CR10X-PB OS v.1.10 (647 KB) 28-03-2006

Execution of this download installs the CR10X PakBus Operating System on your computer.  

Note: The Device Configuration Utility is used to upload the included operating system to the datalogger.  Requires an SC32A or SC32B.


Device Configuration Utility v.2.26 (44.8 MB) 16-03-2021

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 10, 8.1, 8, and 7 (Both 32 and 64 bit)

Ver historial de revisiones

Preguntas frecuentes para

Number of FAQs related to CR10X: 14

Expand AllCollapse All

  1. The red and blue wire in differential channel 5 is a thermocouple. We ship the data logger with this thermocouple so that users can work through sample program #2 in the "CR10X Measurement and Control Module Overview" section of the CR10X manual. Feel free to remove this temperature measurement sensor if it is not needed.

  2. A practical maximum is to connect one multiplexer per every two control terminals on the data logger. Control terminals can be shared between multiplexers to increase the number of connected multiplexers. Sharing terminals, however, requires more complex wiring and programming. Users who would like to connect more than one multiplexer per every two control terminals are advised to contact a sales or support engineer at Campbell Scientific for assistance.

  3. The CR10 and CR10X can use the same wiring panel. The original CR10 wiring panel design was improved by doing the following:

    • Increasing the hole size in the screw terminals to accommodate several wires
    • Adding ground terminals for sensor shield wires
    • Labeling terminals for SDM devices
    • Decreasing the profile to fit inside a 4 in. pipe
    • Improving control port protection
  4. The CR10X has battery-backup RAM and clock. In other words, the program, final storage data, or clock settings are not lost if ac power is lost. Data is sent to final storage by an internal program. Data can be sent by an internal program from final storage to a storage module, computer, or printer using Instruction 96 Active Serial Data Output.

  5. If the CR10X has Modbus OS, Wonderware can be used to display the data. Without the Modbus OS, LoggerNet software would be needed to collect the data and then the PC-OPC Sever software would be used to display the data.

  6. The CR10X uses downloadable operating systems instead of PROMs and includes more instruction in the standard operating system. For a list of instructions included in the standard operating system, refer to the prompt sheet or CR10X manual.

  7. Instruction 15, Control Port Serial I/O, does allow the use of one control port for hardware flow control (RTS/DTR) or (TXD/RXD). The first control port is the (RTS/DTR) line. Baud rate is limited to 300 or 1200. 

Casos de estudio

Egypt: Preserving King Tut's Tomb
In 1922, when the tomb of Tutankhamen was discovered in Egypt's Valley of the Kings,......read more
South Africa: Citrus Research Institute Monitors Exports
South Africa's subtropical climate is favorable for citrus fruit production. South Africa annually exports roughly......read more
California: Coastal Slope Monitoring
The North County Transit District (NCTD) of San Diego County, California, determined that three segments......read more
Pacific Northwest: AgriMet Network
Competition for limited water resources in the western United States is increasing, as are the......read more
Virginia: Tracking Climate Changes in National Park
Forests in the Blue Ridge region are undergoing numerous changes due to: Change in land......read more
Space Farmers
Imagine the bored mind of a space traveler as he looks around the room he......read more
Costa Rica: Banana Production
Campbell Scientific recently supplied agrometeorological stations for an important research project in Costa Rica. The......read more
Delaware: Environmental Observing System
The Delaware Environmental Observing System (DEOS) is a real-time system dedicated to monitoring environmental conditions......read more